- QUICK, EASY APPLICATION -

APPLICATION INSTRUCTIONS

  1. Locate and prepare a suitable surface for your Konsilee product.
  2. Give the surface a wipe over with isopropyl alcohol.
  3. Ensure the surface you are applying your product to is clean and free from any cleaning chemicals.
  4. Ensure the surface is completely dry before attempting to apply the product.
  5. Remove the backing film and place the product on your desired surface, ensuring to apply it in a diagonal direction, from one corner to the other, to minimise air bubbles from forming. 
  6. Important: Leave the product to sit empty and dry for at least 12 hours before use.
  7. You can test the product by applying some downwards pressure to the pocket of the product to ensure it has sufficiently attached to the surface it has been applied to. 
  8. If your surface has calcium present, ensure to completely clean/remove the calcium build-up from the surface prior to applying our holders. 

Important Notes:

Do not apply water to the contact surface prior to product application, as this will not allow the product to properly attach. 

Do not apply products over any grout lines.

Do not overload the product.

Konsilee products are not suitable to store breakable items, such as glass.

Konsilee items are waterproof and have drainage holes, however, they should be cleaned when necessary to ensure cleanliness is maintained. 

- APPLICATION INSTRUCTIONS -

THE KORA | CORNER CADDY

  1. Ensure the surface you are applying your product to is clean and free from any cleaning chemicals.
  2. Give the surface a wipe over with isopropyl alcohol.
  3. Ensure the surface is completely dry before attempting to apply the product.
  4. Hold the caddy up to the corner and position it where you would like it to sit. Take a moment here to line it up, it must be applied straight and level.
  5. Remove one side's backing film and place the opposite side against the wall, slightly out from the corner.
  6. Slide the product straight along the surface, towards the corner softly. Stop once the product first touches the wall.
  7. Check the product has been applied straight, then firmly press all adhesive areas on this side against the wall, ensuring full contact has been made with the surface. Note: Do not push the corner of the caddy tightly into the corner. The design is slightly rounded and is intended to sit just off the corner, not forced into it.
  8. Remove the film from the opposite side, then firmly press this side against the wall, working from the innermost part, outwards.
  9. Important: Leave the product to sit empty and dry for at least 12 hours before use.

Extra Information & Tips:

Our corner caddies are designed without adhesive in the centre corner section, meaning this corner area (only) can sit over the single vertical corner grout line. No other area of the caddy is permitted to be placed over any other grout lines.

You may wish to position the caddy just above a horizontal grout line to help guide a straight, level application.

If this isn't an option, you're welcome to fold an A4 sheet of paper in half and place the folded edge into the corner of your shower, where you intend the bottom of your caddy to sit. Secure it in place with tape or Blu Tack, then apply the caddy directly above the paper, using the straight edge as a guide to ensure the base of the caddy is level.

- EASY TO CLEAN -

PRODUCT CLEANING & CARE

Silicone Cleaning: Use a soft microfibre cloth along with warm, soapy water to clean the silicone of your product/s. Be sure to clean the product pouches, drainage holes, and the inner silicone recess of the shower mirror.

Shower Mirror: Rinse shower mirror with water only, when needed. Do not use cleaning products or cloths to clean the mirror surface, as this can compromise the mirror's surface and fog-resistant coating.

IMPORTANT: Do not use abrasive pads, brushes, or chemical cleaning agents on any of the products, as this may cause damage to the surface and overall appearance.

Product Care 

Clean your products regularly using the above directions, to maintain cleanliness.

Please ensure to use and install our products as directed, as failure to do so can result in the product not functioning as intended. 

Not using the product as directed can result in damage to the product or the items being held within the product. 

Please take care when applying the product by ensuring the area is completely dry, to ensure injury does not occur.